STK290,Steel Coil/Plate/Sheet,External Polyethylene Coating pipe,Stainless Steel Plate

STK290

Elbow,External Asphalt Enamel Coating pipe,Galvanized square tube
STK290,Steel Coil/Plate/Sheet,External Polyethylene Coating pipe,Stainless Steel Plate

STK290

JIS G3444 STK 290 is one of the Japanese Industrial Standarded steel pipes primarily used for the following applications.


Creating pillars (eaves pillars, outside pillars, etc.)


Piles of steel pipe


The building’s pillars are made of STK materials. Steel columns are usually hidden by decorative materials, so steel tubes (columns) with lower cross-section properties than square steel tubes are not used. If, however, the steel column’s form is visible from the outside, utilize a cylindrical steel pipe.

  • CHEMICAL COMPOSITION OF JIS G3444 STK290

    Symbol of grade C Si Mn P S
    STK290 0.050 max. 0.050 max.
    Notes
    a) If necessary, alloying elements other than specified in this table may be added.
    b) For the tube of grade STK540 exceeding 12.5 mm in wall thickness, the chemical composition may be subject to the agreement between the purchaser and the manufacturer.
  • MECHANICAL PROPERTIES OF JIS G3444 STK290

    Symbol of Grade
    Tensile Strength
    N/mm²
    Yield Point of Proof Stress
    N/mm²
    Tensile Strength in Weld Zone
    N/mm²
    Flattening Bendability
    Distance between Plates
    (H)
    Bend Angle Inside Radius
    Applied outside diameter
    All outside diameters All outside diameters All outside diameters All outside diameters 50 mm max.
    STK290 290 min. 290 min. 2/3 D 90° 6 D
    NOTE 1  D of this table is the outside diameter of the tubes.
    NOTE 2  1 N/mm²—1 MPa
    Note a) Standard of bend angle shall be the start point of bending.
  • STK290 TENSILE TEST PIECE AND THE MINIMUM VALUE OF ELONGATION

    Symbol of grade Tube Manufacturing Method
    Seamless and butt welded Electric resistance welded and automatic arc welded All manufacturing methods
    Applied outside diameter
    All outside diameters 350 mm Over 350 mm All outside diameters
    Test Piece and Direction of Test Piece
    No. 11 test piece
    No. 12 test piece
    No. 11 test piece
    No. 12 test piece
    No.5 test piece No.4 test piece
    Tube axis direction Tube axis direction Perpendicular to tube axis direction Tube axis direction Perpendicular to tube axis direction
    STK290 30 30 25 28 23
    For the tubes of outside diameter 40 mm or under, the elongation value in this table shall not be applied. However, the test result for these tubes shall be recorded. Further, the elongation may be specified by agreement between the manufacturer and the purchaser.
  • DIMENSIONAL TOLERANCES OF JIS G3444 STK290

    - Outside Diameter Tolerance a)

    Classification Outside Diameter b)
    Tolerances on
    Outside Diameter c)
    Applicable Division
    Class 1 Under 50mm ± 0.5mm
    Applied when there is no specification.
    Applicable to hot-finished seamless steel tubes.
    50mm or Over ± 1%
    Class 2 Under 50mm ± 0.25mm
    Applied when there is a specification.
    Not applicable to hot-finished seamless steel tubes.
    50mm or Over ± 0.5%
    Notes a) For the local parts such as repaired parts if the wall thickness can be confirmed to be
    within the tolerance in the table below, the outside diameter tolerance of this table need not be applied.
    b) The method for measuring the outside diameter of tubes exceeding 350mm in outside diameter may be determined by the circumferential length. The mutual conversion of outside diameter D and the circumferential length l shall be by the following formula:
    D = l  / π
    Where D: outside diameter (mm)     l: circumferential length (mm)    π:3.1416
    c) The tolerances on the outside diameter of ends of electric resistance welded and automatic
    arc welded steel tubes exceeding 350mm in outside diameter shall be ±0.5%。

    - Wall Thickness Tolerance a)

    Classification For Seamless Steel Tube For Other than Seamless Steel Tube Applicable Division
    Wall Thickness Tolerance of Wall Thickness Wall Thickness Tolerance of Wall Thickness
    Class 1 Under 4mm +0.6mm, -0.5mm Under 4mm +0.6mm, -0.5mm
    Applied when there is no specification.
    Applicable to hot-finished seamless steel tubes.
    4mm or Over +15%, -12.5% 4mm or Over to and excl. 12mm +15%, -12.5%
    12mm or Over +15%, -1.5mm
    Class 2 Under 3mm ±0.3mm Under 3mm ± 0.3mm Applied when there is a specification.
    Not applicable to hot-finished seamless steel tubes.
    3mm or Over ±10% 3mm or Over to and excl. 12mm ±10%
    12mm or Over +10%,-1.2mm
    Notes a) The tolerances on the wall thickness of tubes exceeding 1016.0 mm in outside diameter may be agreed upon between the manufacturer and the purchaser.

  • MARKING OF JIS G3444 STEEL GRADE STK290

    Each tube having passed the inspection shall be marked with the following items on each STK290 tube. For tubes of a smaller outside diameter or when there is a special request by the purchaser, marking may be applied on a bundle. The order of arrangement of the markings is not specified. When approved by the purchaser, part of the items may be omitted.

    Grade symbol

    A symbol representing the manufacturing process. The following symbol should be used to indicate the production technique. However, a space may be used in place of the dash.

      1. As welded steel tube with electric resistance: -E-G

      2. Hot finished electric resistance welded steel tube:  -E-H
      3. Cold finished electric resistance welded steel tube:  -E-C
      4. Butt-welded steel tube:  -B
      5. Automatic arc welded steel tube:  -A
    Measurements Outside diameter and wall thickness should be noted for dimensions.
    The manufacturer’s name or an abbreviation of the manufacturer’s name
    A symbol representing the coating kind (in the case of using coated steel sheet or coated steel strip). The maker and purchaser shall agree on the symbol’s abbreviation.
We use cookies and other tracking technologies to improve your browsing experience on our website, to show you personalized content and targeted ads, to analyze our website traffic, and to understand where our visitors are coming from.