English
Español
Tel : +86-0731-85716039
Email :
S235JRH
S275J2H
S355J2H
S275J0H
S355J0H
S355K2H
| DN | O. D. | W. T. | |||||||||||||||
| Inch | mm | SCH5S | SCH10S | SCH10 | SCH20 | SCH30 | SCH40 | SCH60 | SCH80 | SCH100 | SCH120 | SCH140 | SCH160 | STD | XS | XXS | |
| 50 | 2″ | 60.3 | 1.65 | 2.77 | – | – | – | 3.91 | – | 5.54 | – | – | – | 8.74 | 3.91 | 5.54 | 11.07 |
| 65 | 2 1/2″ | 73 | 2.11 | 3.05 | – | – | – | 5.16 | – | 7.01 | – | – | – | 9.53 | 5.16 | 7.01 | 14.02 |
| 80 | 3″ | 88.9 | 2.11 | 3.05 | – | – | – | 5.49 | – | 7.62 | – | – | – | 11.13 | 5.49 | 7.52 | 15.24 |
| 90 | 3 1/2″ | 101.6 | 2.11 | 3.05 | – | – | – | 5.74 | – | 8.08 | – | – | – | – | 5.74 | 8.08 | – |
| 100 | 4″ | 114.3 | 2.11 | 3.05 | – | – | – | 6.02 | – | 8.58 | – | 11.13 | – | 13.49 | 6.02 | 8.56 | 17.12 |
| 125 | 5″ | 141.3 | 2.77 | 3.4 | – | – | – | 6.55 | – | 9.53 | – | 12.7 | – | 15.88 | 6.55 | 9.53 | 18.05 |
| 150 | 6″ | 168.3 | 2.77 | 3.4 | – | – | – | 7.11 | – | 10.97 | – | 14.27 | – | 18.26 | 7.11 | 10.97 | 21.95 |
| 200 | 8″ | 219.1 | 2.77 | 3.76 | – | 6.35 | 7.04 | 8.18 | 10.31 | 12.7 | 15.09 | 18.26 | 20.62 | 23.01 | 8.18 | 12.7 | 22.23 |
| 250 | 10″ | 273.1 | 3.4 | 4.19 | – | 6.35 | 7.8 | 9.27 | 12.7 | 15.09 | 18.26 | 21.44 | 25.4 | 28.58 | 9.27 | 12.7 | 25.4 |
| 300 | 12″ | 323.9 | 3.96 | 4.57 | – | 6.35 | 8.38 | 10.31 | 14.27 | 17.48 | 21.44 | 25.4 | 28.58 | 33.32 | 9.53 | 12.7 | 25.4 |
| 350 | 14″ | 355.5 | 3.96 | 4.78 | 6.35 | 7.92 | 9.53 | 11.13 | 15.09 | 19.05 | 23.83 | 27.79 | 31.75 | 35.71 | 9.53 | 12.7 | – |
| 400 | 16″ | 406.4 | 4.19 | 4.78 | 6.35 | 7.92 | 9.53 | 12.7 | 16.66 | 21.44 | 26.19 | 30.96 | 36.53 | 40.49 | 9.53 | 12.7 | – |
| 450 | 18″ | 457.2 | 4.19 | 4.78 | 6.35 | 7.92 | 11.13 | 14.27 | 19.05 | 23.83 | 39.36 | 34.93 | 39.67 | 45.24 | – | – | – |
| 500 | 20″ | 508 | 4.78 | 5.54 | 6.35 | 9.53 | 12.7 | 15.09 | 20.62 | 26.19 | 32.54 | 38.1 | 44.45 | 50.01 | – | – | – |
| 550 | 22″ | 558.8 | 4.78 | 5.54 | 6.35 | 9.53 | 12.7 | – | 22.23 | 28.58 | 34.93 | 41.28 | 47.63 | 53.98 | – | – | – |
| 600 | 24″ | 609.6 | 5.54 | 6.35 | 6.35 | 9.53 | 14.27 | 17.48 | 24.61 | 30.96 | 38.89 | 46.02 | 52.37 | 59.54 | – | – | – |
Weldable steels are specified in this European standard. EN 1011-1 and EN 1011-2 specify the main standards for welding products under this European standard.
When welding these products, the greatest danger is the development of cold cracking in the welded zone as the product thickness, strength level, and CEV rise. Cold cracking is a result of a combination of the following factors:
• elevated diffusible hydrogen levels in the weld metal;Please check the table below for the chemical composition requirement of EN 10219 structural hollow sections, thickness ≤ 40mm.
The table below lists the required mechanical properties for EN 10219 structural hollow sections.
EN 10219 is tensile tested according to EN 10002-1 and Charpy impact tested according to EN 10045-1.
| Inspection Requirements | Inspection Frequency | |||
| Type of test |
Non-specific
inspection
|
Specific inspection | ||
|
Mandatory
tests
|
1 | Cast analysis |
One result per delivery
item
|
One per cast |
| 2 | Tensile test |
One result per delivery
item
|
One per test unit ( b) | |
| 3 |
Impact test for
Qualities J2 and K2 only
|
Not applicable | One set per test unit (b) | |
| 4 |
Surface condition
and dimensions
|
– | – | |
| 5 | NDT of the weld | Not applicable | All products, full length | |
|
Optional
tests
|
6 | Product analysis | Not applicable | One per test unit a |
| 7 |
Cast analysis
additional elements
|
Not applicable | See Option 1.2 | |
| 8 |
Impact test for
qualities JR and J0
|
Not applicable | One set per test unit (b) | |
| b – Longitudinal or transverse samples at the discretion of the manufacturer. | ||||
| Inspection Requirements | Inspection Frequency | ||
| Type of test | Specific inspection | ||
|
Mandatory
tests
|
1 | Cast analysis | One per cast |
| 2 | Tensile test | One per test unitF( b) | |
| 3 | Impact test | One set per test unit (b) | |
| 4 |
Surface condition
and dimensions
|
– | |
|
Optional
tests
|
5 | NDT of the weld | All products, full length |
| 6 | Product analysis | One per test unit a | |
| b – Longitudinal or transverse samples at the discretion of the manufacturer. | |||
Each of the square and rectangular hollow sections shall be marked with the following information.
• Specification designation
